#WHO WROTE THE STELLARIUM WEB PAGE FOR FREE#
#WHO WROTE THE STELLARIUM WEB PAGE INSTALL#
#WHO WROTE THE STELLARIUM WEB PAGE SERIAL#
#WHO WROTE THE STELLARIUM WEB PAGE PC#
#WHO WROTE THE STELLARIUM WEB PAGE BLUETOOTH#

Require the last firmware and Stellarium+ >=1.7.You can download Stellarium to your computer for free from or use the web version. Using the SynScan App as a bridge (see above)

#WHO WROTE THE STELLARIUM WEB PAGE BLUETOOTH#

Work both on WiFi (port 9998) and Bluetooth Nexstar Hand Controllers (Nexstar GPS etc.) Require Serial-to-Wifi/Bluetooth/USB Host converterĪutostar #497, Autostar #497EP, Audiostar The following controllers are known to work fine with Stellarium Mobile PLUS: Brand In general, all controllers compatible with some forms of the LX200 protocol, or with NexStar protocol should be auto-detected, even if not specified in the table below.

#WHO WROTE THE STELLARIUM WEB PAGE PC#

You need to select a ‘Network’ link type and use the IP adress of your PC (usually .x) as a host, on port 10000.

You can then connect Stellarium Mobile to your PC by connecting your phone to the same WIFI network, and then inside setup Stellarium Mobile so that it connects to it. On linux this can be done with the socat command line tool using a single command: You can then tell your PC to forward the telescope data to a local TCP socket on which Stellarium Mobile can connect.

#WHO WROTE THE STELLARIUM WEB PAGE SERIAL#

In this case you need to plug the Serial RS232 port of the telescope hand controller to your PC using a (cheap!) Serial to USB cable. It is also possible to use a computer sitting next to the telescope as a bridge. Using a linux computer as a bridge between Stellarium Mobile PLUS and the telescope

#WHO WROTE THE STELLARIUM WEB PAGE INSTALL#

Users can download and install SynScan Pro for Android version 1.19.16 from our website.

A temporary solution is to run the SynScan Pro app in a smaller FreeForm window, a floating window, or a splitting window and run the Stellarium in a larger window if the user’s Android phone supports these features, as shown in the attached picture.

The current SynScan Pro app for Android released on Google Play can not work in the background to provide TCP/UDP server communication.

We have been receiving reports about an issue with Synscan and after contacting the Sky Watcher guys, they acknowledged that there is an issue in the recent SynScan apps version. These settings are OS dependent, but usually it helps to disable the battery saving, set Synscan app to “do not optimise”, or “ignore optimizations”. To solve this issue, it is necessary to change the android settings for SynScan app to avoid it being killed too quickly.

This causes the connection to be lost between Stellarium and the telescope. Warning 2: on some android phones, the OS decides to kill SynScan app when it’s running in the background, presumably because it’s using too much resources or battery. The only way to drive your telescope on iOS using the SynScan app is currently to have it running on another device (either iOS or android). Warning 1: On iOS, it is not possible to have the SynScan app running in the background. Once the telescope is setup, start Stellarium Mobile PLUS (keeping SynScan app running in the background) and connect to it using a “Network” connection type, on host 127.0.0.1, port 11882. The SynScan app opens a TCP socket on the phone on port 11882 emulating a regular SynScan hand controller protocol. For this, you need to install the officialĪpps and use it to connect to the telescope, configure and align it. SynScan-based Wifi mounts such as the SkyWatcher Az-GTi can be controller without hand controller. Using the SynScan app as a bridge between Stellarium Mobile PLUS and the telescope Once you define the type of link between the scope and phone, this is basically it! Stellarium Mobile Plus will try hard to automatically recognize the protocol, the type of mount, and mount status and all other available information about the hardware whenever possible. “BT/USB/TCP Bridge Pro” (1,49€ on Play Store) On Android, for many phones models, it is also possible to connect to the mount using a USB Host adapter cable, and a third party app creating a local TCP socket redirecting ot the USB port. Tested controllers for many type of mounts can be for example found on In many case, the telescope mount hand controller exposes a Serial RS232 port which needs to be plugged into a Serial-to-WIFI or Serial-to-Bluetooth converter so that the phone can access to it. This one works only on Android, because iOS doesn’t allow apps to use Bluetooth SPP. Currently bluetooth 2.0, using SPP profile. This covers Wifi enabled telescopes, LAN connection, or SynScan mounts when using the SynScan app (see below). Network connection (serial over a TCP socket).In order to have your phone talk to the telescope controller, you first need to connect it to your mount or hand controller.

Most (but not all) of the current GOTO telescope are compatible with one of these protocols. Since version 1.1.0 Stellarium Mobile PLUS allows to control a GOTO telescope directly from the phone, by using NexStar/SynScan or LX200 serial protocols.

Who wrote the stellarium web page